Overview
STS 2000 (32 – 120 A) Single Phase Static Transfer Switch
Deltron STS, allows instantaneous transfer of power sources to the load. If one power source fails, the STS switches to the back-up power source so fast that the load never recognizes the transfer made.
STS 2000 1 phase, 2 pole static transfer switch transfers uninterruptedly critical loads to either of two independent AC power lines. The system monitors two AC inputs. If any of them goes out of the specified tolerance, it transfers the critical load to the other. By increasing the energy quality of the systems used with STS 2000, while reducing the effects of interference and short interruptions, a backup power system is gained.
Compact and Rack Type Design
2U / 3U 19" rack chassis with clip-on rear terminals and optional hot-swap frame.
Microprocessor Control
Full digital control with digitally set points, programmable synchronized and unsynchronized transfers.
Hot-Swappable
Optional hot-swap version for maintenance without interrupting the load.
Features
Characteristics
- Increased power quality
- Increase noise reduction
- Power blackout protection
- Power redundancy
- Automatic static switching
- Remote monitoring input power sources
- Easy static and mechanical transfer to input sources
- Remote management the power events
- Power event logging
- Output current capability up to 1000% for short time
- 19” Rack cabinet
- Hot swap option
- Manufactured according to EC Directive: EN62310
- 2 years warranty
General Specifications
- Full digital control with microprocessor controlled structure
- 2 AC inputs with 1 phase and neutral switching
- Easy installation and maintenance
- Compact and rack type design
- Wide input voltage range
- "Break Before Make" type transfer
- Very fast uninterrupted transfer even in case of any failure (4 ms for synchronised sources)
- Selectable preferred source
- Fuse-free construction with a robust, high reliability SCR
- Digitally controlled system set points
- Programmable synchronized and unsynchronized transfers
- Isolation protection between sources with switched neutral
- Convenient and multifunctional front panel and diagnostic codes
- Transfer inhibit system over a certain current value
- Overload, over temperature and short circuit protections
- Convenience during maintenance and repair with Isolated Maintenance Bypass
- Remote monitoring of energy resources
- TCP/IP, SNMP, MODBUS and RS232 infrastructure for communication
- Dry-contact interface
- Internal cooling fans
- Hot-swap feature (Optional)
- Optional external AC power supply socket outlet
- Optional SNMP adaptor
Technical specifications
STS 2000 (32 – 120 A) Single Phase Static Transfer Switch – technical data
| Model | STS2032 | STS2063 | STS2120 |
|---|---|---|---|
| Nominal current | 32 A | 63 A | 120 A |
| Electrical data | |||
| Input voltage | 220/230/240 VAC 1P + N + G | ||
| Input voltage range | 180 – 264 VAC (Ph-N) | ||
| Input frequency | 50 Hz / 60 Hz | ||
| Input frequency range (operation range adjustable) | 46 – 54 Hz (for 50 Hz); 56 – 64 Hz (for 60 Hz) | ||
| Transfer type | "Break before make" | ||
| Transfer methods available | Automatic / manual / remote | ||
| Transfer control | Synchron; with adjustable delay (non synchron); zero current (non synchron) | ||
| Transfer time | ≤ 4 msec for synchronous sources; ≤ 10 msec for non-synchronous sources | ||
| Switching type | 1 phase + neutral switching (2-poles) | ||
| Output current crest factor | 3:1 | ||
| Admissible overload | 0 – 100% continuous; 101 – 150% 1 minute; 151 – 200% 10 seconds; > 200% 250 msec | ||
| Protections | Output overload and short circuit protection, overtemperature protection, backfeed protection | ||
| LCD panel and mimic | Standard | ||
| Communication | RS232 standard, RS485 optional, SNMP optional | ||
| TCP/IP connection | Optional | ||
| Dry contacts | 3 programmable relay outputs | ||
| Breaking current capacity (SW1, SW2) | 10 kA | ||
| Environmental data | |||
| Cooling | Forced cooling (redundant fans) | ||
| Cooling air direction | From front to rear | ||
| Operating temperature | 0 °C – 40 °C | ||
| Storage temperature | −10 °C up to +50 °C | ||
| Relative humidity | 90% max. (non-condensing) | ||
| Protection degree | IP20 | ||
| Standards | EN62310-1, EN62310-2 | ||
| Max. operation height | 1000 m at nominal current rating | ||
| Acoustic noise | < 50 dBA | < 50 dBA | < 52 dBA |
| Mechanical data | |||
| Weight (kg) | 12 | 13 | 20 |
| Dimensions (standard) | 2U (19" rack), width = 485 mm, depth = 545 mm | 2U (19" rack), width = 485 mm, depth = 545 mm | 3U (19" rack), width = 485 mm, depth = 605 mm |
| Dimensions (hot-swap) | 2U (19" rack), width = 485 mm, depth = 590 mm | 2U (19" rack), width = 485 mm, depth = 590 mm | 3U (19" rack), width = 485 mm, depth = 645 mm |
| Power cables connection | Clip-on terminals (on the rear panel) | ||
Downloads
Datasheets & manuals
Official Deltron documents for STS 2000 (32 – 120 A) Single Phase Static Transfer Switch. All files are PDF.
Related products
More STS models
STS 3000
STS 3000
Deltron STS, allows instantaneous transfer of power sources to the load. If one power source fails, the STS switches to the back-up power source so fast that the load never recognizes the transfer made.
View details STS 4000
STS 4000
Deltron STS, allows instantaneous transfer of power sources to the load. If one power source fails, the STS switches to the back-up power source so fast that the load never recognizes the transfer made.
View details